RFC 10052
Performance Measurement with Asymmetrical Traffic Using the Simple Two-Way Active Measurement Protocol (STAMP)
RFC 10052 is a Proposed Standard published in September 2026 in the IETF stream by the ippm working group.
Proposed Standard IETF stream ippm WG Operations and Management
- Citations
- Cites 13 RFCs
Abstract
This document defines an optional extension to the Simple Two-way Active Measurement Protocol (STAMP) that enables a Session-Reflector to send asymmetrical packets, that is, response packets whose size or quantity differs from those sent by the Session-Sender. While standard STAMP exchanges are symmetrical, certain measurement scenarios benefit from reflected packets of different lengths or additional responses to better approximate application traffic conditions. The extension specifies the Reflected Test Packet Control TLV and associated procedures, analyzes challenges in active performance measurement (including in multicast environments), and describes STAMP behaviors to improve measurement efficiency and reduce network impact.
Plain text 42 KB · rfc-editor.org · Datatracker · doi:10.17487/RFC10052 · draft-ietf-ippm-asymmetrical-pkts-14
Internet Engineering Task Force (IETF) G. Mirsky
Request for Comments: 10052 Ciena Corporation
Category: Standards Track E. Ruffini
ISSN: 2070-1721 OutSys
H. Nydell
Cisco Systems
R. Foote
Nokia
W. Hawkins
University of Cincinnati
September 2026
Performance Measurement with Asymmetrical Traffic Using the Simple Two-
Way Active Measurement Protocol (STAMP)
Abstract
This document defines an optional extension to the Simple Two-way
Active Measurement Protocol (STAMP) that enables a Session-Reflector
to send asymmetrical packets, that is, response packets whose size or
quantity differs from those sent by the Session-Sender. While
standard STAMP exchanges are symmetrical, certain measurement
scenarios benefit from reflected packets of different lengths or
additional responses to better approximate application traffic
conditions. The extension specifies the Reflected Test Packet
Control TLV and associated procedures, analyzes challenges in active
performance measurement (including in multicast environments), and
describes STAMP behaviors to improve measurement efficiency and
reduce network impact.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 7841.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
https://www.rfc-editor.org/info/rfc10052.
Copyright Notice
Copyright (c) 2026 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Revised BSD License text as described in Section 4.e of the
Trust Legal Provisions and are provided without warranty as described
in the Revised BSD License.
Table of Contents
1. Introduction
2. Conventions Used in This Document
2.1. Terminology
2.2. Acronyms
2.3. Requirements Language
3. Reflected Test Packet Control TLV
3.1. Address Group Sub-TLVs
3.1.1. Layer 2 Address Group Sub-TLV
3.1.2. Layer 3 Address Group Sub-TLV
4. Operational Considerations
4.1. Rate Measurement
4.1.1. Operational Considerations for Performing Rate
Measurement
4.2. Active Performance Measurement in a Multicast Environment
4.3. Using Reflected Test Packet Control TLV in Combination with
Other TLVs
5. Security Considerations
6. IANA Considerations
6.1. Reflected Test Packet Control TLV Type
6.2. Conformant Reflected Packet STAMP TLV Flag
6.3. Layer 2 and Layer 3 Address Group Sub-TLV Types
7. References
7.1. Normative References
7.2. Informative References
Acknowledgments
Authors' Addresses
1. Introduction
The Simple Two-way Active Measurement Protocol (STAMP) [RFC8762]
defines the base STAMP functionalities. STAMP Optional Extensions
[RFC8972] introduces a TLV structure that allows a Session-Sender to
include optional instructions for Session-Reflectors to extend the
functionality of the base STAMP protocol. New STAMP TLVs can be
defined to support scenarios like the ones described in [RFC7497],
which discusses the coordination of messaging between the source and
destination to help deliver one of the fundamental principles of IP
performance metric measurements, minimizing the test traffic effect
on user flows.
By default, a STAMP Session-Sender and a Session-Reflector exchange
packets symmetrically: The number of packets sent by the Session-
Reflector and the Session-Sender are the same, and the length of the
packets sent by the Session-Reflector and the Session-Sender are the
same. However, in some scenarios, e.g., rate measurements discussed
in [RFC7497], it would be beneficial for a Session-Reflector to
respond with asymmetrical test packets: packets whose length is not
symmetrical to the test packet sent by the Session-Sender and/or
packets that are not sent in direct response to a packet received
from a Session-Sender. The optional extension defined in this
document gives operators the tools to create such asymmetrical
packets between a Session-Sender and a Session-Reflector.
Measurement of performance metrics in a multicast network using an
active measurement method (Section 3.4 of [RFC7799]) has specific
challenges compared to what operators experience monitoring in a
unicast network. This document analyzes these challenges and
specifies procedures and STAMP extensions to achieve more efficient
measurements with a lesser impact on a network.
2. Conventions Used in This Document
2.1. Terminology
This document uses terms defined in [RFC8762], specifically Session-
Sender, Session-Reflector, and symmetrical packets.
This document uses terms defined in [RFC8972], specifically STAMP
Session Identifier (SSID), STAMP TLV Flags, and Sub-TLVs.
This document uses terms defined in [RFC7497], specifically In-
Service and Out-of-Service.
In this document, "asymmetrical packets" has two meanings, depending
on the context. The first aspect is asymmetry in packet size between
a packet sent by a Session-Reflector and the packet it received from
the Session-Sender. The second aspect is asymmetry in the number of
packets the Session-Reflector transmits in response to receiving a
single STAMP-Test packet.
In this document, a multicast network means a communication network
model where a sender transmits a single packet addressed to a
multicast group, and the network delivers copies of that packet to
multiple receivers that have joined the group.
2.2. Acronyms
CE: Congestion Experienced
ECN: Explicit Congestion Notification
EUI: Extended Unique Identifier
MAC: Media Access Control
STAMP: Simple Two-way Active Measurement Protocol
TLV: Type-Length-Value
2.3. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Reflected Test Packet Control TLV
This section defines an additional optional STAMP extension, the
Reflected Test Packet Control TLV, and an additional bit flag in the
STAMP TLV Flags field. The format of this TLV is presented in
Figure 1.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|STAMP TLV Flags| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Length of the Reflected Packet |Number of the Reflected Packets|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Interval Between the Reflected Packets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Sub-TLVs ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 1: Reflected Test Packet Control TLV Format
The descriptions of the fields are as follows:
STAMP TLV Flags: A one-octet field [RFC8972].
Type: A one-octet field that identifies the Reflected Test Packet
Control TLV. This field is set to 12 (Section 6.1).
Length: A two-octet field. The value is variable and MUST NOT be
smaller than 12 octets.
Length of the Reflected Packet: A two-octet field. The value is an
unsigned integer that is the requested length of a reflected test
packet in octets.
Number of the Reflected Packets: A two-octet field. The value is an
unsigned integer that is the number of reflected test packets that
the Session-Reflector is requested to transmit in response to
receiving a STAMP-Test packet with the Reflected Test Packet
Control TLV.
Interval Between the Reflected Packets: A four-octet field. The
value is an unsigned integer set to the interval in nanoseconds
between the transmission of the consecutive reflected test packets
in response to receiving a STAMP-Test packet with the Reflected
Test Packet Control TLV.
Sub-TLVs: An optional field that includes additional information
communicated by a Session-Sender.
Also, an additional STAMP TLV flag [RFC8972], the Conformant
Reflected Packet, has been allocated by IANA in the "STAMP TLV Flags"
registry (Section 6.2): the one-bit C flag (3). A Session-Sender
MUST zero this flag on transmission, and the Session-Reflector MUST
ignore its value on the receipt of a STAMP-Test packet with a STAMP
TLV.
A Session-Sender MAY include the Reflected Test Packet Control TLV in
a STAMP test packet. If the received STAMP-Test packet includes the
Reflected Test Packet Control TLV, the Session-Reflector MUST
transmit a sequence of reflected test packets according to the
following rules:
* The length of the reflected test packet MUST be the largest of:
a. The length of a base Session-Reflector packet in the mode
(unauthenticated or authenticated) of the received STAMP-Test
packet, as defined in Section 4.3 of [RFC8762], including all
STAMP extension TLVs [RFC8972] present in the received STAMP-
Test packet but excluding any Extra Padding TLVs. The
rationale to exclude any Extra Padding TLVs present in
combination with the Reflected Test Packet Control TLV is to
support a scenario in which a Session-Reflector is requested
to transmit a sequence of packets shorter than the received
STAMP packet.
b. The value in the Length of the Reflected Packet field of the
Reflected Test Packet Control TLV aligned at a four-octet
boundary.
In a case where the length of the reflected packet calculated by this
rule is longer than the length of the reflected packet calculated by
the rules in Section 4 of [RFC8972], the Session-Reflector MUST use
the Extra Padding TLV (Section 4.1 of [RFC8972]) to increase the
length of the reflected test packet. If the calculated length of the
reflected packet exceeds the maximum transmission unit (MTU) of the
interface to reach the Session-Sender, the Session-Reflector MUST set
the Conformant Reflected Packet STAMP TLV flag (Section 6.2) to 1 and
MUST transmit a single reflected packet of the length equal to the
MTU of the egress interface. Otherwise, the Session-Reflector MUST
set the C flag to 0 in each reflected test packet.
The number of reflected test packets in the sequence MUST equal the
value of the Number of the Reflected Packets field.
If the value of the Number of the Reflected Packets field is greater
than 1, the interval between the transmission of two consecutive
reflected packets in the sequence MUST be equal to the value in the
Interval Between the Reflected Packets field in nanoseconds. To
prevent excessive congestion caused by reflected packets, a Session-
Reflector that supports the Reflected Test Packet Control TLV MUST
enforce limits on both the data rate (bytes per second) and the total
data volume (bytes) of the STAMP payload it generates in response to
an incoming test packet. If a test packet is received that would
generate traffic that exceeds either of these limits, the Session-
Reflector MUST set the C flag (Section 6.2) to 1 and MUST transmit a
single reflected packet of the length calculated by the rules listed
above. Otherwise, the Session-Reflector MUST set the C flag to 0 in
each reflected test packet.
If the Number of the Reflected Packets field is set to 0, the
Session-Reflector MUST NOT send any reflected packets. Furthermore,
in this case, the Session-Reflector SHOULD discard the received
STAMP-Test packet. However, a local policy MAY override this default
behavior and specify an alternative handling. Note that this
behavior of the Session-Reflector is demonstrated when the Control
Code Flags field of the Return Path Control Code sub-TLV
(Section 4.1.1 of [RFC9503]) is set to No Reply Requested. If this
is the intended behavior, use of the Return Path TLV is preferable.
Each reflected test packet in the sequence is formed according to
Section 4.3 of [RFC8762].
As defined above, there are two cases when a Session-Reflector will
set the C flag in the reflected packet. To disambiguate which case
led to the C flag being set to 1, an implementation of a Session-
Sender can determine the cause as follows:
* If the length of the received reflected STAMP packet is less than
the value of the Length of the Reflected Packet field, the
requested length exceeds the MTU of the egress interface of the
Session-Reflector.
* If the length of the received reflected STAMP packet equals the
value of the Length of the Reflected Packet field, the requested
data rate and/or the data volume exceed the limits set at the
Session-Reflector.
3.1. Address Group Sub-TLVs
A multicast network that uses an active performance measurement
method for In-Service rate estimation MUST include a rate control
mechanism that bounds and regulates the generation of measurement
packets. Because multicast replication can amplify probe traffic
across the distribution tree, uncontrolled probe emission risks
introducing congestion, altering traffic asymmetry, or otherwise
perturbing the conditions being measured. The rate control mechanism
MUST ensure that probe traffic remains non-intrusive, predictable,
and consistent with the operational characteristics of the multicast
topology. Aligning probe generation behavior with the timing and
packet selection semantics of the asymmetric packet measurement
method makes it possible for observations collected at receivers to
remain valid and comparable. To allow for deployment on networks
with different characteristics (i.e., latency, throughput, etc.),
implementations SHOULD provide operators with the ability to
configure rate limits and pacing parameters that prevent excessive or
uneven probe replication while still enabling statistically
meaningful measurement samples.
3.1.1. Layer 2 Address Group Sub-TLV
An optional Layer 2 Address Group sub-TLV is a variable-length sub-
TLV that includes a Layer 2 Address Group Mask and Address Group
fields used by the Session-Sender to select the Session-Reflectors
for a response. The Layer 2 Address Group sub-TLV can convey EUI-48
(Extended Unique Identifier), EUI-64 [IEEE-802.3-2022], and a 16-bit
short address for local identification within a Personal Area Network
[IEEE-802.15.4-2024]. The format of the Layer 2 Address Group sub-
TLV is presented in Figure 2.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Sub-TLV Flags| Sub-TLV Type | Sub-TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Layer 2 Address Group Mask (variable length) ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Layer 2 Address Group (variable length) ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: Layer 2 Address Group Sub-TLV Format
Where:
Sub-TLV Flags: An eight-bit field. The format, values, and
interpretation of flags are as defined for STAMP TLV Flags
[RFC8972]. Flag values are taken from the "STAMP TLV Flags"
registry [IANA-STAMP].
Sub-TLV Type: A one-octet field. IANA has assigned value 10
(Section 6.3).
Sub-TLV Length: A two-octet field whose value equals the length of
the Value field of the Layer 2 Address Group sub-TLV in octets.
Because the lengths of the Layer 2 Address Group Mask and Layer 2
Address Group fields MUST be equal, valid values for the Sub-TLV
Length are 4, 12, and 16. Any other value MUST be considered by
the Session-Reflector as a malformed sub-TLV.
The Value field of the Layer 2 Address Group sub-TLV consists of the
following fields:
Layer 2 Address Group Mask: A field that represents the bitmask to
be applied to all MAC addresses associated with the Session-
Reflector. The length of the field is 1/2 the value of the sub-
TLV Length field.
Layer 2 Address Group: A field that represents the group to which
this TLV is addressed. The length of the field is 1/2 the value
of the sub-TLV Length field.
If the Session-Reflector applies the value of the Layer 2 Address
Group Mask field (using a bitwise AND) to any of its MAC addresses
with the same length and the result is equal to the value of the
Layer 2 Address Group field, then the Session-Reflector MUST stop
processing the Layer 2 Address Group sub-TLV and continue processing
the received test packet. If no matches are found, the Session-
Reflector MUST stop processing the received packet.
3.1.2. Layer 3 Address Group Sub-TLV
An optional Layer 3 Address Group sub-TLV is a variable-length sub-
TLV that includes the IP Prefix and IP Prefix Length fields used by
the Session-Sender to select the Session-Reflectors for a response.
The format of the Layer 3 Address Group sub-TLV is presented in
Figure 3.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sub-TLV Flags | Sub-TLV Type | Sub-TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Prefix Length | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ IP Prefix ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: Layer 3 Address Group Sub-TLV Format
Where:
Sub-TLV Flags: An eight-bit field. The format, values, and
interpretation of flags are as defined for STAMP TLV Flags
[RFC8972]. Flag values are taken from the "STAMP TLV Flags"
registry [IANA-STAMP].
Sub-TLV Type: A one-octet field. IANA has assigned value 11
(Section 6.3).
Sub-TLV Length: A two-octet field whose value equals either 8 (if
the IP Prefix is the prefix for an IPv4 address) or 20 (if the IP
Prefix is the prefix for an IPv6 address). Any other value MUST
be considered by the Session-Reflector as a malformed sub-TLV.
The Value field of the Layer 3 Address Group sub-TLV consists of the
following fields:
Prefix Length: A one-octet unsigned integer field that contains the
length, in bits, of the prefix of the value in the IP Prefix
field.
Reserved: A three-octet field. The field MUST be zeroed on
transmission and ignored on receipt.
IP Prefix: A variable-length field. The length of the field is four
octets if the IP Prefix is the prefix for an IPv4 address or 16 if
the IP Prefix is the prefix for an IPv6 address.
When processing this sub-TLV, the Session-Reflector will construct an
IP mask according to the value, n, in the Prefix Length field. The
IP mask will be an IP address (of the family specified by the value
of the sub-TLV Length field, according to the semantics above) where
the n most-significant bits are set to 1 and all other bits are set
to 0. Once the mask is constructed, if the Session-Reflector applies
it (using a bitwise AND) to any of its IP addresses of the same
family and the result is equal to the value in the IP Prefix field,
then the Session-Reflector MUST stop processing the Layer 3 Address
Group sub-TLV and continue processing the received test packet. If
no matches are found, the Session-Reflector MUST stop processing the
received packet.
4. Operational Considerations
4.1. Rate Measurement
[RFC7497] defines the problem of access rate measurement in access
networks. One of the essential requirements identified for a test
protocol is the ability to control packet characteristics on the
tested path, such as asymmetric rate and asymmetric packet size. The
Reflected Test Packet Control TLV, defined in Section 3, conforms to
the requirements for measuring access rate by providing optional
controls of the number of reflected test packets, the size of the
reflected packet(s), and the time interval, i.e., rate, in
transmitting the sequence of the reflected test packets. The access
rate metric and method of access rate measurement are out of the
scope of this document. The UDP Speed Test (see [RFC9097] and
[RFC9946]) also allows for the measurement of access bandwidth.
4.1.1. Operational Considerations for Performing Rate Measurement
General considerations for using a testing protocol for rate
measurement are documented in Section 7 of [RFC7497]. These
considerations are specific for In-Service and Out-of-Service rate
measurement. In the Out-of-Service testing, an operator may use a
very high traffic rate and/or volume (i.e., high values for the
Length of the Reflected Packet and/or Number of the Reflected Packets
fields, and/or low values for the Interval Between the Reflected
Packets field of the Reflected Test Packet Control TLV) to create
congestion in the bottleneck. However, when performing In-Service
rate testing, an operator may start with a low rate and/or volume and
gradually increase them with each transmitted Reflected Test Packet
Control TLV.
A service subscriber performing extensive rate measurements on the
operational network SHOULD consider bullet item 6 in Section 11 of
[RFC9946] and be mindful of limits placed on their service by the
Service Provider. In particular, active measurement can lead to the
generation of data volumes that may cause those performing the test
to violate service-level agreements with their Service Provider.
4.2. Active Performance Measurement in a Multicast Environment
For performance measurements using STAMP in a multicast environment,
a Session-Sender is expected to be the root and Session-Reflectors
are the leaves of the same multicast distribution tree. The
mechanism of constructing the multicast tree is outside the scope of
this document.
According to [RFC8972], a STAMP Session is demultiplexed by a
Session-Reflector by the tuple that consists of source and
destination IP addresses, source and destination UDP port numbers, or
the source IP address and STAMP Session Identifier. That is also the
case when monitoring the performance of a multicast flow, despite the
fact that the destination IP address is a multicast address.
Therefore, there is no special behavior defined for a Session-
Reflector upon receiving a STAMP-Test packet over a multicast tree.
It processes the packet according to [RFC8762] and [RFC8972]. The
Session-Reflector MUST use the source IP address of the received
STAMP-Test packet as the destination IP address of the reflected test
packet and MUST use one of the IP addresses associated with the node
as the source IP address for that packet. As a result, a Session-
Sender may receive multiple replies from multiple counterpart
Session-Reflectors. Such a Session-Sender may include a Reflected
Test Packet Control TLV and include either a Layer 2 Address Group
sub-TLV or a Layer 3 Address Group sub-TLV to limit the Session-
Reflectors that respond.
The multicast environment itself could be configured to help
alleviate the possibility that network congestion may occur if a
single test packet generates a large number of concurrent replies,
all directed to the same endpoint. Depending on the multicast
implementation, adding the Reflected Test Packet Control TLV could
allow the multicast environment to limit the number of replies by
modifying the Reflected Test Packet Control TLV sub-TLV values of any
STAMP packets it sees, allowing replies only from reflectors that
are:
* Randomly selected, by specifying a Layer 2 Address Group sub-TLV:
for example, setting the EUI-48 Address Group Mask to 0xF and the
EUI-48 Address Group to 0x1. As a result, only 1 out of 16
reflectors will reply;
* Hosted on a specific vendor Network Interface Card, by specifying
a Layer 2 Address Group sub-TLV with the EUI-48 Address Group Mask
set to 0xFFFFFF000000; and
* Belonging to specific IP networks, for example, a subnet dedicated
to IPv6-over-IPv4 encapsulation, by specifying the appropriate
Layer 3 Address Group sub-TLV.
Multicast traffic is also intrinsically asymmetrical. The upstream
(source-to-receiver) direction typically dominates, while the return
path receives limited attention because multicast communication is
primarily one-to-many and generates comparatively little downstream
or receiver-to-source traffic. The value of the Length of the
Reflected Packet field can be used to ensure that the reflected
packet transports all the timestamps and requested information, which
are crucial for the underlying measurement, but is as short as
possible so as not to flood the network with useless data.
4.3. Using Reflected Test Packet Control TLV in Combination with Other
TLVs
[RFC9503] defines the Return Path TLV that, when used in combination
with the Return Address Sub-TLV, allows a Session-Sender to request
the reflected packet be sent to a different address from the Session-
Sender one. These STAMP extensions could be used in combination with
the Reflected Test Packet Control TLV, defined in this document, to
direct the reflected STAMP-Test packets to a collector of measurement
data (according to [RFC7594]) for further processing and network
analytics. An example of the use case is a multicast scenario when,
for example, the Session-Sender is close to the actual multicast
source (such as a camera transmitting live video) so that the test
packets follow the same path as the video stream packets in one
direction but the reflected test packets follow another to a
destination where the data would be analyzed.
For compatibility with [RFC9503], a Session-Sender MUST NOT include a
Return Path Control Code sub-TLV with the Control Code Flags set to
No Reply Requested in a test packet that also contains a Reflected
Test Packet Control TLV with a non-zero value. A Session-Reflector
that supports both TLVs MUST set the U flag to 1 in both the Return
Path and Reflected Test Packet Control TLVs within the reflected
STAMP packet. Furthermore, the Session-Reflector SHOULD log a
notification to inform an operator about the misconstructed STAMP
packet.
The Reflected Test Packet Control TLV can be combined with the Class
of Service TLV [RFC8972] to augment rate testing or testing in a
multicast network that monitors the consistency of Differentiated
Services Code Point and ECN values in forward and reverse directions
of the particular STAMP-Test session.
5. Security Considerations
Security considerations discussed in [RFC7497], [RFC8762], [RFC8972],
and [RFC9503] apply to this document. Furthermore, spoofed STAMP-
Test packets with the Reflected Test Packet Control TLV can be
exploited to conduct a Denial-of-Service (DoS) attack. Hence,
implementations MUST use an identity protection mechanism. For
example, the Session-Reflector may verify the information about the
source of the STAMP packet against a pre-defined list of trusted
nodes. Furthermore, an implementation that supports this
specification MUST provide administrative control of support of the
Reflected Test Packet Control TLV on a Session-Reflector with it
being disabled by default. Also, either the STAMP authentication
mode [RFC8762] or the HMAC (Hashed Message Authentication Code) TLV
[RFC8972] SHOULD be used for a STAMP-Test session containing the
Reflected Test Packet Control TLV. Note that if integrity protection
is enabled, any in-path modification will cause verification to fail
unless the modifying element is within the trust boundary and can
recompute the integrity check.
Furthermore, a DoS attack using the Reflected Test Packet Control TLV
might target the STAMP Session-Reflector by overloading it with test
packet reflection, e.g., minuscule intervals and/or an excessive
number of concurrent test sessions. To mitigate that, a Session-
Reflector implementation that supports the new TLV MUST provide a
mechanism to limit the reflection rate and volume of STAMP-Test
packets (see Section 3 for a detailed discussion).
Considering the potential number of reflected packets generated by a
single test packet sent to a multicast address, parameters in the
first STAMP-Test packet with the Reflected Test Packet Control TLV
MUST be selected conservatively. Consider the Number of the
Reflected Packets field value set to one. As a result, a Session-
Sender, by counting the packets reflected after originating a first
STAMP-Test packet with the Reflected Test Packet Control TLV, can
evaluate the load caused by using the Reflected Test Packet Control
TLV in which more than a single reflected packet to the same
multicast destination is requested. To further mitigate the risk of
using the Reflected Test Packet Control TLV in a multicast network, a
Session-Sender SHOULD sign packets using the HMAC TLV when sending
such messages in unauthenticated mode [RFC8762]. But even with the
HMAC TLV, the Reflected Test Packet Control TLV could be exploited by
a replay attack. To mitigate that risk, a STAMP Session-Reflector
SHOULD use the value of the Sequence Number field [RFC8762] of the
received STAMP-Test packet. If that value compared to the received
value in the previous test packet of the same STAMP-Test session is
not monotonically increasing, then the Session-Reflector MUST respond
with a single reflected packet, setting the U flag to 1 [RFC8972].
That may not indicate a replay attack, but there is packet re-
ordering or packet duplication in the network. An operator can use
other diagnostic methods to characterize and localize the problem.
An implementation of the Session-Reflector can use the Serial Number
Arithmetic [RFC1982] or any of the other methods to verify the
correct ordering of test packets.
A Session-Sender SHOULD NOT send the next STAMP-Test packet with the
Reflected Test Packet Control TLV before the Session-Reflector is
expected to complete the transmission of all reflected packets in
response to the Reflected Test Packet Control TLV in the previous
test packet. In some scenarios, the Reflected Test Packet Control
TLV might induce congestion on the transient bottleneck. Section 10
of [RFC9097] specifies security requirements for capacity
measurements with asymmetric UDP loads.
When planning In-Service capacity measurement, operators SHOULD
follow recommendations formulated in Sections 3 and 7 of [RFC7497].
If the underlay network is ECN-capable, a Session-Reflector may
receive STAMP-Test packets with the ECN field marked as Congestion
Experienced (CE). ECN markings provide an indication of incipient
congestion rather than packet loss. However, the interpretation of
what constitutes "significant congestion" and the operational
thresholds for reacting to ECN-CE depend on the specific deployment,
service objectives, and operator policy. Operators should be aware
that In-Service capacity measurements may influence congestion
conditions, potentially contributing to ECN-CE marking in the
network. Implementations and operational procedures SHOULD ensure
that the use of STAMP for In-Service measurement does not
unintentionally degrade data traffic or lead to misinterpretation of
ECN-related congestion signals. Appropriate thresholds and
mitigation actions remain deployment-specific and SHOULD be guided by
operator policy and network performance objectives.
Furthermore, Section 3.1.5 of [RFC8085] determines that a UDP
congestion control SHOULD respond quickly to experienced congestion
and account for loss rate and response time when choosing a new rate.
And Section 8.1 of [RFC9097] specifies the load rate adjustment
algorithm with its sample pseudocode offered in Appendix A of
[RFC9097].
6. IANA Considerations
6.1. Reflected Test Packet Control TLV Type
IANA has assigned a new value for the Reflected Test Packet Control
TLV in the "STAMP TLV Types" registry under the "Simple Two-way
Active Measurement Protocol (STAMP) TLV Types" registry group as
follows:
+=======+===============================+===========+
| Value | Description | Reference |
+=======+===============================+===========+
| 12 | Reflected Test Packet Control | RFC 10052 |
+-------+-------------------------------+-----------+
Table 1: Reflected Test Packet Control TLV Type
6.2. Conformant Reflected Packet STAMP TLV Flag
IANA has allocated a bit position for the Conformant Reflected Packet
STAMP TLV flag in the "STAMP TLV Flags" registry under the "Simple
Two-way Active Measurement Protocol (STAMP) TLV Types" registry group
as follows:
+==============+========+=============+===========+
| Bit position | Symbol | Description | Reference |
+==============+========+=============+===========+
| 3 | C | Conformant | RFC 10052 |
+--------------+--------+-------------+-----------+
Table 2: Conformant Reflected Packet STAMP TLV Flag
6.3. Layer 2 and Layer 3 Address Group Sub-TLV Types
IANA has assigned values for the Layer 2 Address Group and Layer 3
Address Group sub-TLV Types in the "STAMP Sub-TLV Types" registry
under the "Simple Two-way Active Measurement Protocol (STAMP) TLV
Types" registry group as follows:
+=======+=======================+================+===========+
| Value | Description | TLV Used | Reference |
+=======+=======================+================+===========+
| 10 | Layer 2 Address Group | Reflected Test | RFC 10052 |
| | | Packet Control | |
+-------+-----------------------+----------------+-----------+
| 11 | Layer 3 Address Group | Reflected Test | RFC 10052 |
| | | Packet Control | |
+-------+-----------------------+----------------+-----------+
Table 3: STAMP Sub-TLV Types for the Reflected Test Packet
Control TLV
7. References
7.1. Normative References
[IANA-STAMP]
IANA, "STAMP Sub-TLV Types",
<https://www.iana.org/assignments/stamp-tlv-types>.
[RFC1982] Elz, R. and R. Bush, "Serial Number Arithmetic", RFC 1982,
DOI 10.17487/RFC1982, August 1996,
<https://www.rfc-editor.org/info/rfc1982>.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC7497] Morton, A., "Rate Measurement Test Protocol Problem
Statement and Requirements", RFC 7497,
DOI 10.17487/RFC7497, April 2015,
<https://www.rfc-editor.org/info/rfc7497>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8762] Mirsky, G., Jun, G., Nydell, H., and R. Foote, "Simple
Two-Way Active Measurement Protocol", RFC 8762,
DOI 10.17487/RFC8762, March 2020,
<https://www.rfc-editor.org/info/rfc8762>.
[RFC8972] Mirsky, G., Min, X., Nydell, H., Foote, R., Masputra, A.,
and E. Ruffini, "Simple Two-Way Active Measurement
Protocol Optional Extensions", RFC 8972,
DOI 10.17487/RFC8972, January 2021,
<https://www.rfc-editor.org/info/rfc8972>.
[RFC9503] Gandhi, R., Ed., Filsfils, C., Chen, M., Janssens, B., and
R. Foote, "Simple Two-Way Active Measurement Protocol
(STAMP) Extensions for Segment Routing Networks",
RFC 9503, DOI 10.17487/RFC9503, October 2023,
<https://www.rfc-editor.org/info/rfc9503>.
[RFC9946] Morton, A., Ciavattone, L., and R. Geib, Ed., "The UDP
Speed Test Protocol (UDPSTP) for One-Way IP Capacity
Metric Measurement", RFC 9946, DOI 10.17487/RFC9946, April
2026, <https://www.rfc-editor.org/info/rfc9946>.
7.2. Informative References
[IEEE-802.3-2022]
IEEE, "IEEE Standard for Ethernet", IEEE Std 802.3-2022,
DOI 10.1109/IEEESTD.2022.9844436, July 2022,
<https://doi.org/10.1109/IEEESTD.2022.9844436>.
[IEEE-802.15.4-2024]
IEEE, "IEEE Standard for Low-Rate Wireless Networks",
IEEE Std 802.15.4-2024, DOI 10.1109/IEEESTD.2024.10794632,
December 2024,
<https://doi.org/10.1109/IEEESTD.2024.10794632>.
[RFC7594] Eardley, P., Morton, A., Bagnulo, M., Burbridge, T.,
Aitken, P., and A. Akhter, "A Framework for Large-Scale
Measurement of Broadband Performance (LMAP)", RFC 7594,
DOI 10.17487/RFC7594, September 2015,
<https://www.rfc-editor.org/info/rfc7594>.
[RFC7799] Morton, A., "Active and Passive Metrics and Methods (with
Hybrid Types In-Between)", RFC 7799, DOI 10.17487/RFC7799,
May 2016, <https://www.rfc-editor.org/info/rfc7799>.
[RFC8085] Eggert, L., Fairhurst, G., and G. Shepherd, "UDP Usage
Guidelines", BCP 145, RFC 8085, DOI 10.17487/RFC8085,
March 2017, <https://www.rfc-editor.org/info/rfc8085>.
[RFC9097] Morton, A., Geib, R., and L. Ciavattone, "Metrics and
Methods for One-Way IP Capacity", RFC 9097,
DOI 10.17487/RFC9097, November 2021,
<https://www.rfc-editor.org/info/rfc9097>.
Acknowledgments
The authors thank Zhang Li, Ruediger Geib, Rakesh Gandhi, Giuseppe
Fioccola, Xiao Min, Greg White, and Rohan Bhosle for their thorough
reviews and helpful suggestions, which improved the document.
Authors' Addresses
Greg Mirsky
Ciena Corporation
Email: gregimirsky@gmail.com
Ernesto Ruffini
OutSys
Email: eruffini@outsys.org
Henrik Nydell
Cisco Systems
Email: hnydell@cisco.com
Richard Foote
Nokia
Email: footer.foote@nokia.com
Will Hawkins
University of Cincinnati
Email: hawkinsw@obs.cr
Contents 28
- Abstract
- Status of This Memo
- Copyright Notice
- Table of Contents
- 1 Introduction
- 2 Conventions Used in This Document
- 2.1 Terminology
- 2.2 Acronyms
- 2.3 Requirements Language
- 3 Reflected Test Packet Control TLV
- 3.1 Address Group Sub-TLVs
- 3.1.1 Layer 2 Address Group Sub-TLV
- 3.1.2 Layer 3 Address Group Sub-TLV
- 4 Operational Considerations
- 4.1 Rate Measurement
- 4.1.1 Operational Considerations for Performing Rate Measurement
- 4.2 Active Performance Measurement in a Multicast Environment
- 4.3 Using Reflected Test Packet Control TLV in Combination with Other
- 5 Security Considerations
- 6 IANA Considerations
- 6.1 Reflected Test Packet Control TLV Type
- 6.2 Conformant Reflected Packet STAMP TLV Flag
- 6.3 Layer 2 and Layer 3 Address Group Sub-TLV Types
- 7 References
- 7.1 Normative References
- 7.2 Informative References
- Acknowledgments
- Authors' Addresses